• Highly visible Organic EL display with high resolution metering to offer both VU and Peak level with selectable Stereo and Mono indication
• Master, Trim and HPF knobs with pop up mechanism to avoid inadvertent operations
• Mixer\\\'s parameter setting status (mic/line, phantom on/off, etc) can be seen on the display
• Wealth of outputs such as Sub output, Tape output, 2 x Phones out as well as AUX output with
  channel select
• Switchable level settings at +4/0/ -20/ -60 on Main and Sub outputs
• Phones outs accept standard and mini plugs on each socket with multiple source and PFL monitoring
• A dedicated monitor return input to check the audio from VTR or Camera feeds
• AUX input can be merged to the Stereo bus for cascade connection
• Analog limiter with the threshold and ratio adjustments
• DC output with Hirose connector for powering a wireless receiver
  
  The FM3 uses an Internal 8 x AA batteries or DC12-24V external powering.  It has more than 7 hours operation with alkaline batteries (phantom off). The remaining battery capacity can be displayed on both the display and LED indicator.
   Analog Inputs

• INPUT 1 through INPUT 3 Connector:
  XLR-3-31 type (transformer balanced)
  Input impedance: 10ohms or more
  Nominal input level: -20 dBu to +4 dBu
  Maximum input level: +29 dBu
• MIC input
  Input impedance: 2ohms or more
  Nominal input level: -70 dBu to -30 dBu
  Maximum input level: -5 dBu
• AUX IN
  Connector: XLR-5-51 type (electronically balanced)
  Input impedance: 20ohms or more
  Nominal input level: +4 dBu
  Maximum input level: +29 dBu
• RTN
  Connector: 3.5mm stereo mini-phone jack (unbalanced)
  Input impedance: 10 ohms or more
  Nominal input level: -10 dBV
  Maximum input level: +15 dBV

Analog Outputs

• MAIN OUT (L, R) Connector:
  XLR-3-32 type (transformer balanced)
  Applicable load impedance: 600ohms or more
  Nominal output level: +4, 0, -20 or -60 dBu (switchable)
  Maximum output level: +24, +20, 0 or -40 dBu (switchable)
• SUB OUT
  Connector: XLR-5-52 type (electronically balanced)
  Applicable load impedance: 10ohms; or more
  Nominal output level: +4, 0, -20 or -60 dBu (switchable)
  Maximum output level: +24, +20, 0 or -40 dBu (switchable)
• TAPE OUT
  Connector: 3.5mm stereo mini-phone jack (unbalanced)
  Applicable load impedance: 10ohms or more
  Nominal output level: -10 dBV
  Maximum output level: +10 dBV
• AUX OUT
  Connector: 3.5mm stereo mini-phone jack (unbalanced)
  Applicable load impedance: 10ohms or more
  Nominal output level: -10 dBV or -60 dBV (switchable)
  Maximum output level: +10 dBV or -40 dBV (switchable)
• PHONES
  Connectors : 1/4 stereo phone jack and 3.5mm stereo mini-phone jack
  Applicable load impedance: 8ohms or more
  Maximum output power: 50mW (at 32ohms load, THD: 0.1% or less?

Others

• DC IN
  Connector: XLR-4-32 type (male)
  Input voltage: DC10V to DC 24V
• DC OUT
  Connector: Hirose 4 pin (female)
  Applicable plug: Hirose HR10A-7P-4P
  Output voltage: DC7.2V - 24V (Max. 0.5A)
  Frequency response
• LINE IN - MAIN OUT: 20Hz to 20kHz +/- 1dB (reference level)
• MIC IN - MAIN OUT: 40Hz to 20kHz +/- 1dB (reference level)
• HEADPHONES (32ohms load, 25mW output power): 20Hz to 20kHz +/- 3dB
• S/N ratio (A-weighted)
• LINE (INPUT GAIN: +4 dBu): 80dB or better
• MIC (INPUT GAIN: -70dBu: 55dB or better (equivalent input noise: -125 dBu)
• Total harmonic distortion: 0.1? or less at 1 kHz
• Headphones residual noise (PHONES level control at minimum) -72 dBV or less (A-weighted)
• Crosstalk: -70 dB or less at 1kHz
• Phantom power: P48 (phantom 48V) and T12 (A-B 12V) power supply circuit for each input channel.
  T12 power supply can be disabled or enabled using the status mode.
• HPF (High pass filter) 40Hz to 300Hz, -12dB/oct. The cutoff frequency is continuously sweepable.
• Slate microphone / slate tone
  Slate tone: 1kHz
  Slate microphone: built in the unit
• Level meter
  VU and peak level meters
  Stereo/mono metering selectable
• Limiter
  Attack time: approximately 5 msec.
  Release time: approximately 200 msec.
  Threshold level: +6dBu or +12dBu at +4dBu output level
  Ratio: 3:1 or 5:1
  Threshold level and ratio can be selected using the status mode.

Physical
 

• External Dimensions: 188 (W) x 53 (H) x 159 (D) mm (Including protrusions)
• Weight: Approximately 1.2kg (not including the internal batteries)
• Power: Internal batteries: Eight AA batteries (alkaline: 12V, nickel hydride: 9.6V)
• Power requirement: DC7.2 to 12V
  External power supply: Optional AC adaptor
  Recommended external battery voltage: DC12 to 24V
  Power requirement: DC9 to 24V
• Power consumption:
  Approximately 4.0W
• Supplied accessories:
  Battery box, Owner\\\'s manual