Sound Devices USB Pre 2 Interface

Sound Devices USB Pre 2 Interface
Sound Devices USB Pre 2 InterfaceSound Devices USB Pre 2 InterfaceSound Devices USB Pre 2 InterfaceSound Devices USB Pre 2 Interface

Sound Devices USB Pre 2 Interface

Sound Devices’ USBPre® 2 is a high-resolution, portable hardware interface for Mac- and Windows-based digital audio. The USBPre 2 is the industry's highest performance and most flexible portable interface, connecting professional microphones, line-level sources, consumer audio electronics, and S/PDIF digital sources with Mac OS and Windows computers via USB.

Precision Microphone Preamplifiers

USBPre 2 includes two discrete-transistor microphone preamps with 24-bit converters and sampling rates up to 192 kHz. These preamplifiers provide the highest performance in any portable interface. Their topology is shared with Sound Devices award-winning 744T Digital Audio Recorder. Peak limiters, high-pass filters, and a 15 dB pad provide overload protection. All analog-to-digital and digital-to-analog conversion is performed by the USBPre 2 for superior audio performance.

Computer Connectivity

USBPre 2 is a class-compliant audio device. This allows for simple plug-and-play connection to computers running Mac OS, Windows, and Linux (see note to the right on Class-Compliant Drivers). There are no drivers to install for the USBPre 2 and there are no software-only features. All additional controls and settings are available on back panel DIP switches. The USB port also provides power to the unit, both when connected as an audio interface and when used in Stand-Alone operation.

Output Connectivity Flexibility

To interconnect with sound systems big and small, the USBPre 2 includes numerous output connection types, including balanced mic- or line-level on XLR, unbalanced consumer line-level on RCA, S/PDIF coaxial (RCA) and optical (Toslink). The outputs have their own, dedicated front-panel level control. Use the balanced line-level signals to connect to powered loudspeakers. Use the optical S/PDIF to connect to hi-fi systems. Use the coaxial S/PDIF output in Stand-Alone mode for a portable microphone preamplifer with digital output for any production application.

Informative Metering

Accurate signal level metering is essential for any sound engineer. The USBPre 2 includes a 23-segment, multicolor LED meter for precise level indication. The meter is switchable between input signal metering and playback signal metering. The meter indicates both VU and peak (PPM) ballistics.

Stand-Alone Operation

The USBPre 2 can be used in Stand-Alone mode where it operates as a high-quality, portable microphone preamplifier and analog-to-digital converter. Digital signals connected to the USBPre 2 are converted to analog and available at the headphone, XLR, and RCA outputs. Stand-Alone operation requires the unit to be connected to a USB power source. Stand-Alone mode is a great option when an additional microphone preamplifer, A-D converter, or D-A converter is required.

Field-Tested Reliability

Like all of Sound Devices products, the USBPre 2 is designed to stand up to the most demanding environments. Its extruded aluminum chassis and aluminum panels, machined knobs, metal connectors, and laser-etched nomenclature are designed to hold up to years of abuse.

Class Compliant Drivers

As a class-compliant audio device, the USBPre 2 is limited to a maximum data rate of 24-bit, 48 kHz in Windows, Linux, and Mac OS versions 10.4 to 10.5.7. Mac OS 10.5.8 and higher support the audio class 2.0 device and can address the USBPre 2 up to 24-bit, 192 kHz.

 
 

“ Astoundingly versatile analogue/digital input-analogue/digital output interface unit. First choice for laptop based recording solution. Can be USB bus powered. Slightly complicated DIP switch settings. Excellent mixing capability. 48v Phantom power and headphone monitoring make this unit amazing. ” - Pinknoise Systems.

Specifications

Frequency Response (reference 1 kHz, at 96 kHz Sample Rate) 10 Hz - 40 kHz, ± 0.5 dB (any input to PC recording)
10 Hz - 40 kHz, ± 0.5 dB (PC source to AUX output)
THD+N (22 Hz - 22 kHz measurement bandwidth) 0.05% max (any input to PC recording, gain control at min, input driven to -6 dB FS)
0.009% max (AUX output, 0 dB V output, 100 ohm load)
0.05% max (HEADPHONES output, 2 V rms output, 600 ohm load)
E.I.N. (MIC inputs) -127 dBu min (22 Hz - 22 kHz bandwidth, 150 ohm source, gain control fully clockwise, 15 dB pad out)
Input Clipping Level (1% THD) Mic: -10 dBu
Mic (15 dB pad): +4 dBu
Line: +28 dBu (19.45 V rms)
Aux: +9 dBu (2.18 V rms)
Input Sensitivity (typical, for 0 dB FS) Mic: -9 dBu min, -60 dBu max
Mic (15 dB pad): +6 dBu min, -58 dBu max
Line: +29 dBu min, +10 dBu max
Aux: +12 dBu min, -7 dBu max.
Input Impedance (actual) Mic: 4k ohm, active-balanced
Mic (15 dB pad): 4k ohm, active-balanced
Line: 60k ohm, active-balanced
Aux: 80k ohm, active-balanced
Input Limiter Threshold Mic: -4 dBFS
Low Cut Mic: 80 Hz, -3 dB, 12 dB per octave
Output Clipping Level (1% THD, PC-controlled output levels at max) Balanced XLR: +18 dBu with 100k ohm load
Aux: +8 dBu (2.0 V rms) with 100k ohm load
Headphones: +11 dBu (2.75 V rms) with 600 ohm load
Output Impedance Headphone (Actual): 22 ohms
Balanced XLR (Line level): 500 ohms
Balanced XLR (Mic level): 5 ohms
Aux: 2k ohms
S/PDIF Digital 24 or 16 bit input
A/D Converter 24-bit resolution. 114 dB typical dynamic range (22 Hz - 22 kHz bandwidth, A-weighted)
D/A Converter 24-bit resolution. 112 dB typical dynamic range (22 Hz - 22 kHz bandwidth, A-weighted)
Sample Rates / Bit Depths Recording: 8, 16, or 24-bit at 8, 16, 32, 44.1, 48, 96, or 192 kHz
Playback: 24-bit at 8, 16, 32, 44.1, 48, 96, or 192 kHz
Master Clock Crystal based, low jitter
Metering 48 segments, 44 dB total range, peak ballistics. 0 dB on meter = 0 dB FS (0 dB referenced to full scale digital)
Phantom Power 48 V through 6.8k ohm resistors. Each mic input will supply 10 mA
Powering USB bus powered, soft-start meets USB hot-plugging power requirements (5 V, 100 mA max current drawn during enumeration)
5 V, 500 mA max current from USB port (USBPre 2 will not function if connected through a passive USB connection or hub)
Dimensions (unpackaged) 4.3 cm x 18 cm x 10 cm (H x W x D)
1.7 in. x 7.25 in. x 4.25 in. (H x W x D)
Weight 0.5 kg
1.13 lbs.
Certifications Meets FCC Part 15 Class B
Complies with the Requirements of European Directive 89/336/EEC

Delivery Services

At Pinknoise Systems we like to offer our customers a wide choice of delivery options for their orders, and our prices are affordable and competitive. We also use only the best, most reliable couriers and delivery services to get your equipment where it needs to be - quickly and securely. Please find an outline of our services, prices and timescales below.

Service Timescale Price
UK Mainland Royal Mail Small Parcel 2-4 Days £3.99
UK Offshore Royal Mail 2-4 Days £9.99
UK Standard Courier 2-4 Days £6.49
UK Express Courier Next Day £7.99
International Shipping From 1-8 Days (Full Details) From £15.00

Delivery Times

Delivery times are based on when the packages leaves our premises. Sometimes, due to stock restrictions or a non completed order, delivery may take longer as there is a delay with dispatch. We will always notify customers of any issues and problems via email or telephone. If your order is urgent or details change please do let us know.

For full details, fees, and time schedules, please see our Delivery Information page.

Returns & Refunds

New items: You can return goods you have ordered from us for any reason, at any time within 7 working days of receipt, for a full refund or for an exchange for a different product from our range. The cost of returning goods to us shall be borne by you, the customer, in all circumstances without exception.

Items must be packed suitably and insured for full loss in the event of a delivery problem. Pinknoise Systems will not be responsible for lost or damaged return goods. Lost or damaged goods may effect the level of refund you receive.

Used items: Please note this does not apply to used item unless they are deemed faulty.

For full details of our returns policy, please click here.

Be the first to Write a Review for this item!

£899.00 £990.00
Saving Of:  £91.00 (9%)
(£749.17 Exc. VAT)
+

Availability:  

SPECIAL ORDER  

SPECIAL ORDER

Delivery hours
UK ORDERS: Order soon for delivery on using our express service

Model:  SD-USBPRE2
Part No.:  USBPRE2.0
Manufacturer:  Sound Devices

Sound Devices
Contact us for advice

Need advice? Give us a call

(+44) 01453
825 802

International Delivery

International delivery

We ship across Europe and around the world and have a multitude of shipping options available to our international customers during the checkout, including express delivery for urgent orders.

NEXT DAY DELIVERY

We ship across Europe and around the world and have a multitude of shipping options available to our international customers during the checkout, including express delivery for urgent orders.

FINANCE AVAILABLE

Spread the cost to maximise your capital. Just call our helpful sales team on 01453 825 802, from 9.30am - 5.30pm, to discuss these options and find out what's available to you.

We accept PayPal, Visa, Mastercard, Maestro, American Express

Sound Devices USB Pre 2 Interface

£899.00
CUSTOMERS ALSO BOUGHT
Sanken COS-11D PT Lavalier Microphone (w/ Options)
Sanken COS-11D PT Lavalier Microphone (w/ Options)
  • Overcomes digital transmitter RFI. Water Resistant
  • Durable Design. Great Clear and Rich Sound
  • 4 Color Choices. Improved Moisture Resistance
  • Optimized for the Human Voice
Only 10 in stock  Only 10 in stock
£270.00  £348.48
× Site Currency
£0.00